*The product in the image may differ from the actual product. *All caliper supports for 40mm pitch are designed with "brembo 40mm casting caliper".Since the offset is 26.5mm at the center, please adjust with the attached shim when you use it with AP and NISSIN calipers.(Not compatible with 6POT calipers.) *The supplied shims are also effective in correcting product errors in individual calipers. *Changing calipers and rotors will change the contact surface between the rotors and pads.In such a case, scrape off the surface of the pad that does not contact the rotor and use it. *Caliper bolt pitch brembo 40mm: P1.5 *There may be changes in product specifications due to the manufacturer's reasons.
Caliper support to combine calipers with 40mm or 65mm mounting pitch with standard size rotor. The material is machined aluminum with anodized finish to ensure high strength and durability. Two colors, silver and black, are available to match the color of the caliper and bottom case.(Except for some models)
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I bought these adapters for my front wheel and fork conversion on my Vfr700 rc24.They fitted without any problems. I now have the best brakes I could have on the VfrView Detail
The quality is excellent and the Brembo caliper comes to the center perfectly without shim without error. However, note that the Support is much lower than the Normal caliper, so the hose length will be about 5 cm shorter than the Normal. I use Daytona's extended hose. It looks like AGRASSupport's position is not that different from Normal caliper for less Offset.View Detail
Front forkTZr on RZ250 (3ma) I purchased this product to equip a Brembo caliper to a vehicle of The texture is good and fitting is no problem. I think it looks good with the meat removed.View Detail
I bought this car to install Brembo caliper. It has a nice texture and comes with a Shim for Centering out. Some people don't like wearing Caliper support because it looks like Caliper is hanging down, but I like it a lot. The supplied Bolt is an ordinary Stainless Steel Bolt with a strength rating of A2-70. What is A2-70? If you're wondering, look it up. I'm sure it's not a problem because it's made by PartsManufacturer, but I don't think there are many OEM manufacturers that use A2-70 bolts to fix Caliper. So I changed the bolt to a stronger one, but be careful if you change the bolt. Because it is not a common M10-1.25. Brembo caliper is M10-1.5. It was Exactly 25mm in length. (bremboP4Casting)View Detail
Parenthesis by Aluminum Cut-out! It's so accurate, you can put it on as is, and it comes with a Shim for when you need it. I highly recommend it.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!