[Specification] ・Rated voltage: DC12V ・Outer diameter dimension: W25.5mm x H30.5mm x D15.5mm (*excluding protruding parts)
[Components] ・SPI-110 C1 main unit x 1 ・Model Specific Harness x 1 ・Various double-sided tapes ・Instruction manual *Components vary by kit.
*When the clutch is depressed while driving, the display shows a gear other than the one in which the clutch is engaged, but this is not a malfunction. *Prioritize safety while driving and do not be careless in front.
*Please do not use non-resistive spark plugs.If you use a plug without resistance, noise may be generated and the rotation signal may not be input correctly, so please use a spark plug with resistance. *Please put the attached double-sided tape on the back side of this product to prevent water from entering because there is a switch. *Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage. *After installing this product, periodically inspect it to see if any parts have fallen off. *PROTEC is not responsible for any damage or accident caused by the use of this product. *Protec is not responsible for any labor charges for removal or other expenses incurred during repair. *All vehicles that have been tested by Protec are stock.There is a possibility that a problem may occur if the vehicle is equipped with aftermarket parts other than stock parts. *Please refer to the service manual of your motorcycle to confirm the respective wiring before installation.
●All the necessary parts are included in this kit!Easy installation with special harness! It can be installed easily without soldering because it uses a special harness for each model. *The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design! The main unit dimensions are W25.5mm X H30.5mm X D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility! Equipped with a dimmer sensor [automatic dimming function].The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator! Since the rpm can be set arbitrarily, it can be used for everything from narrowing to preventing over-revving.The blue LED will light up when the rotation is higher than the set value. *You can re-register as many times as you like.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
As for use, there is no problem at all when SHIFT UP, but there are many false indications when Downshift is used. This may be due to the fact that the Shift display is determined by the number of revolutions and speed when connected to Clutch, but it is not very helpful when Downshift is performed all at once after Clutch is turned off at the time of Red signal. Also, it is GOOD that it has one extra power supply take-out Wiring!
Installation is easy with Couplet-on to NORMALWiring, but there was no room in the Light case and it would not close. We managed to get it to fit after some maneuvering, but in the end it took more than 30 minutes. The Instruction Manual says to install it on the top of the Meter, but I stuck it on the panel under the Meter because the Bracket was unreliable and it did not seem to fit well.View Detail
It does not become a talk.....--inferior goods.It sent to the Manufacturer. > -- the number of a Shift position does not come out probably ..... it has replaced with the thing with the wiring mistake of a Harness, and another Harness.Although
, next a Position were set to Ok, the display number of daytime stops being in sight, and it becomes normal.A display becomes thin clearly (it becomes the brightness of night mode).Business is not done daytime. It returned again.What kind of inspection was completely conducted ? .
The thing with the wiring mistake of a Harness, the Harness, and the new article of an indicator body have been sent again....... It is the same as before and a display is not in sight. Not to mention it is not repaired, it indicates to exceeding fixed rotational frequency by a blue Lamp, but it is not displayed.Furthermore, it worsened.
It is although I have you exchange again when it tells attaching as it is and placing and a cause is known until a cause is known, since sending is troublesome for the time being....... Do you do kindly??? ???. .View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!