Seat has a hole in it and my butt is wet, so I replaced it.
With a big Stapler, it wasn't too hard.
Glad to see you're clean.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
5 / 5
1 Review
rating breakdown
5 Stars | 1 | |
---|---|---|
4 Stars | 0 | |
3 Stars | 0 | |
2 Stars | 0 | |
1 Stars | 0 |
Seat has a hole in it and my butt is wet, so I replaced it.
With a big Stapler, it wasn't too hard.
Glad to see you're clean.
I purchased the Super Dio AF28 for the Super Dio AF28.
It stretches well and can be stretched neatly.
The quality is good enough.
However, unlike OEM, there are seams in each part, so this is a concern for water seepage.
Third-party products are probably all the same, so with that in mind, this is a good enough product.
Size feel is good.
The design, cutting, and sewing are both fit, sturdy, and good.
Since the product comes folded, the folds will be visible even if it is stretched at first.
However, it grew and disappeared over time.
Well and pulling and stretching seem to be important.
The cost performance is excellent because the price is reasonable and the quality is adequate.
I felt I could buy Repeat.View Detail
To reupholster my partner due to age and deterioration.
It was the product I ordered.
Thank you for the fast response.
I am satisfied with the Large change in terms of quality cosmetics.
I look forward to working with you again when the opportunity arises.View Detail
Fits: HONDA SMARTDio Z4 AF63 , HONDA SMARTDio DX AF57 , HONDA SMARTDio AF56 , HONDA , HONDA
I've torn the Seat on my moped Scooter, so I'm thinking of putting a Cover on it that can be One-touch mounted with Rubber.
I thought about reupholstering it, but if I was going to do that, I wanted to reupholster it properly like a new car, so I bought a Kawi.
Tucker was easy because I was able to rent an Air tool (Air Tucker) and I have a Compressor at home.
Even if you don't have the equipment, you can use a HandTucker sold at Daiso for about 500 yen to do the job.
However, make sure you have a needle (core) with a short foot. I used a width of 10mm and a foot of 6mm.
The Tucker cores that often come with TuckerBody have long legs, and if you use them to reupholster your Seat, they will stick out on the surface, so please don't use them.
Please refer to youtube and other sites for more information on how to do this.
Decide before and after, Quantity:Pair (for Left and Right) Decide on ... and hit the Tucker while pulling on the diagonal.
If you cut the excess part at the end, the opening and closing of Helmet in (Seat) also becomes smooth.
The finish is much better than the so-called Rubber type Cover, and it feels good ~.
I'm glad I took the DIY challenge to reupholster the seat, because cracks and holes in the seat can cause rainwater to seep into clothes, which is uncomfortable.View Detail
Fits: YAMAHA JOG ZR , YAMAHA JOG 3YK , YAMAHA JOG 3YJ , YAMAHA , YAMAHA
Glue from the back of the Seat cover seam to protect the Seat Sponge from moisture. and installed on top of the Sponge covered with Polyethylene Seat. It was. You will need a strong Tucker to install it. It can be used normally.View Detail
Fits: YAMAHA JOG ZR , YAMAHA JOG 3YK , YAMAHA JOG 3YJ , YAMAHA , YAMAHA
The Seat was torn, so I replaced it with a new Seat The texture is so new
It slips when you sit down At first, I thought it was inevitable
Later, if you've never replaced a new Seat, you'd better get a motorcycle shop to do it for you!View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Customer Service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING